Forklift capacities range from about 3,000 lbs up to more than 70,000+ lbs. You can find the rated capacity of a forklift on its data plate. OSHA requires “only loads within the rated capacity of a truck shall be handled.” It’s easy to think the rated capacity is the same as maximum capacity, but it’s not that simple.

## What is the rated capacity of a forklift?

A forklift’s rated load capacity is the maximum weight in kilograms that a forklift can safely lift and transport at a specified load centre distance in millimetres. This rated load capacity is listed on the forklifts name plate or load capacity data plate.

## How is forklift capacity calculated?

The maximum Load Moment for a truck is derived by multiplying the weight rating of the forklift by the center load distance. If we multiply the 5,000-pound capacity of our theoretical forklift by its 24-inch center load, we arrive at a maximum Load Moment of 120,000 inch-pounds.

## Where is the maximum rated capacity for the forklift located?

At 29 CFR 1910.178(o)(2), OSHA states that “only loads within the rated capacity of a truck shall be handled.” The rated capacity can be found on the “data plate” located on the forklift. You can see an example data plate below.

## How do you calculate the rated capacity of a forklift at different height?

A couple of simple calculations are all that’s necessary:

- Divide the load center as stated on the data plate by the actual load center (in the example above, that would be 24/36=. 6666).
- Multiply this result by the rated load capacity (4000X. 6666=2666.6).

5.03.2013

## How much weight can a 10k forklift lift?

Max. Lift Height: | At Reach Length: | Lift Capacity: |
---|---|---|

34 feet Vertical | 14 feet Extended | 10,000 lbs. |

38 feet Vertical | 18 feet Extended | 8,000 lbs. |

44 feet Vertical | 24 feet Extended | 6,000 lbs. |

55 feet Vertical | 29 feet Extended | 5,000 lbs. |

## Which side of the forklift is supporting more weight?

Weight distribution refers not only to the weight of the load, but also the weight of the forklift itself. An empty forklift has most of its weight in the rear, but when a load is placed on the lift, the weight distribution moves forward.

## How do you calculate load capacity?

Take the total weight of the load and divide this by the number of legs supporting the load. For example, assume a 2,000 pound load is to be supported by 2 legs of a sling. The above will give a total minimum weight on each leg of the sling of 2,000 pounds divided by 2 legs or 1,000 pounds.

## How do you calculate safe load capacity?

SWL or WLL are calculated by dividing MBL by a safety factor (SF). An example of this would be a chain that has a MBL of 2000 lbf (8.89 kN) would have a SWL or WLL of 400 lbf (1.78 kN) if a safety factor of 5 (5:1, 5 to 1, or 1/5) is used.

## How much weight can a forklift hold?

Forklift capacity is the measurement of how much weight a particular forklift can lift. Lower capacities begin around 3,000 lbs. and can go up to over 50,000 lbs.

## How do I choose a forklift?

A Few Quick Tips for getting the Best Forklift

- Find a Trustworthy Brand.
- Think about What you Really Need (a good partner will help you figure that out)
- Know what kind of power you need (think about best fuel type and tire options)

## What is a forklift load chart?

A forklift data plate contains essential information about the forklift, such as its operating weight, rated maximum capacity, model and serial numbers, any present attachments, and it load capacity chart. … Others provide this information as a chart to highlight the differences between the different factors.

## What is rated load capacity?

Rated Capacity is the maximum total load a crane can lift for a defined configuration. Rated Capacity is also known as the Maximum Rated Capacity (MRC) or Manufacturer’s Rated Capacity. … This is referred to as the Gross Load of the crane where the Net Load is the actual mass being lifted.

## What is the load Centre distance on a forklift?

A load center is the horizontal distance from the vertical face of the forks to the center of gravity of the load. As a general rule, load center is 24″ from the face of the forks (the center point of standard 48” x 48” pallet). Forklift capacities range from about 3,000 lbs up to more than 70,000+ lbs.

## How do you calculate electrical panel load?

To calculate the total load on the breaker panel, you simply need to add together the amperage ratings from each circuit breaker, and then multiply that sum by 120 volts.